The VAS 6154diagnostic tool can be used on all 2000+ VW Audi Skoda vehicles including NEW AND FUTURE MODELS in production via wireless network. Here we have collected the most frequently asked questions from customers and offered the corresponding answers.
Volkswagen & Audi introduced component lock (anti-theft/immobilizer) function to their newer transmission control modules to help fighting unauthorized swap of the control unit. If a TCU/TCM is faulty and has been replaced, a component unlock is therefore required.
Note: You don’t need to unlock the unit if you choose to clone the SW from your original unit to the new one.
Typical error messages:
Contains Component protection (Component protection active) The control unit is currently associated with a VIN other than the vehicle VIN or the control unit VIN
You need the following tools to perform component unlock:
VAG diagnosis tool (like VAS5054A, VAS 6154) to connect to your vehicle ODIS software A VW/Audi account depending on the vehicle
Procedure for unlocking TCU:
Run a diagnosis in your ODIS software Locate and select the entry “Component protection” Click on “Perform test…” Click on “Done/Continue” Enter the required information. (Activation number can be your own record number) Enter your VW/Audi online account credentials Click on “OK” On success, ODIS should display “The component protection base programming has been carried out successfully.” Click on “Done” Follow the instructions provided by ODIS End of your component base programming Go back to the test screen and you should see a green check mark before component protection Perform basic settings using guided functions Erase your previous fault codes You may now load your SW into the TCU if needed. If you don’t have the flash program, you may contact your Shing Hoi representative.
Problem: One customer is asking why he cannot open Auto ECU Programmer V2.25 KTAG red PCB software on CD. And it gives a warning “Program already running”. What the reason, any suggestions?
solution ktag red pcb program already running issue – Solution: KTAG Red PCB “Program already running” Issue – KTAG Red PCB Program already running
Solution
1. Please DO NOT open K-TAG ECU Programmer on CD directly. Users should copy it to desktop firstly, then can be running. 2. The reason why this message coming is because user has already opened KTAG software. Please DO NOT open it repeatedly. Or users may try to shut down task firstly, then restart it again.
Highlights of GM MDI2: 1.Multi-Languages available:English, French, German,Italian.etc. Total 30 languages to choose 2.Can do cars from 1990-2019.07 Year 3.you can select the package with HDD( software ) or not , we already installed the GM MDI 2 software into 500G SATA interface laptop HDD,the HDD can be used after 2008 year SATA hard disk interface laptop 4.Support 2010-2019.07 year new cars
Part 1: How to solve GM MDI2 Global TIS V32 cannot be found
Customer problem:
It will not connect with global tis v32 tried on 3 different laptops. MDI manager finds and connects the gm mdi2 device but global tis has a red X through the device when trying to select it, see images attached. Are you able to help via remote still need help asap? Thanks! The solution offered by OBD2.ltd engineer:
The global TIS software you installed is old, and it only can be activated on Windows XP. Please change the XP system.
Part 2: How to Solve GM MDI2 Not Connected to MDI Problem
I bought the GM MDI 2 package from OBD2 last week. I installed the MDI Manager software along with HDD but when I tried to connect the MDI device it asked me to recover the MDI software because the one is out of date. So when I try to update the GM MDI device an error occurs every time. And at the end, after a few seconds the device automatically disconnects and I can do nothing with it. I cannot connect again and the device seems dead.
I made several attempts to update/recover the MDI device but with no luck.
Obd2.ltd engineer replied: Please uninstall GM MDI Manager, and install this new version by the following download link:
Frequently reported by North American customers CAT Caterpillar ET Diagnostic Tool（9PIN connector）connect with Cat Vehicle，CAT Caterpillar ET the indicator light is off and the device can not work. Picture as below:
Have replaced with new CAT Caterpillar ET Diagnostic Tool，the result still same.
We checked the connector of CAT Vehicle，found the problem:
It turns out that some of the CAT Vehicle connector are not standard, can not be match our 9 pin connector of the device.
The connector of our customer’s CAT Vehicle as below:
CAT Caterpillar ET Diagnostic Tool 9PIN connector as below：
The comparison is as follows (on the left is the diagnostic socket of the car, on the right is the 9PIN connection line of the CAT device):
Vehicle connection is: A – Battery Negative B – Battery Positive C – J1939 Data Link+ D – J1939 Data Link- E – J1939 Shield F – J1587 Data Link+ G – J1587 Data Link- H – not connected J – not connected
CAT Diagnostic Tool 9PIN Cable is ： A – Battery Positive B – Battery Negative C – J1587 Data Link+（J1708 Data Link+） D – J1587 Data Link-（ J1708 Data Link-） E– J1939 Data Link+ F – J1939 Data Link- G – CDL+ H – CDL- J（I） – not connected
Contrast:
Some CAT Vehicle’s connector not match with our CAT Diagnostic Tool 9PIN Connector. Even the positive and negative poles of the power supply is opposite. So the device will not work and get power from the vehicle.
How to solve such problem:
Customer need to connect the correct diagnostic connector to the corresponding 9 pin diagnostic connector of the CAT device with the cable. So the device can get power from the vehicle and work normally.
This article lists the newest represented FAQs plus Customers Review on Launch X431 Pad V diagnostic scanner, expressing its Quality & Authenticity.
Q1: Can PAD V scanner be used to do Air bag reset for a 2011 Ford Explorer? A1: The airbag cannot be reset. If the airbag is damaged, you need to replace it and match it.
Q2: Will this Launch scanner do diagnostic and function tests on a 2001 ford 7.3l diesel? A2: Yes. the heavy Duty Software can be subscribed in 2021.6. you can purchase it in the mall or contact us to get the factory price and you can directly use the heavy duty software without connectors. it works pretty well with the smart box.
Q3: Can this be used to reprogram a new ecu for a2008 bmw x3 e83? A3: Sure! this automotive scanner supports reprogram a new ecu for a2008 bmw x3 e83. it comes with the J2534 protocol to replace the existing software / firmware in the ECU; program new ECUs.Fix the vehicle drivability, fuel efficiency, power loss, fault codes and durability issues.
Q4: With this scan tool, am i able to reprogram transmissions, ECUs, sensors, dual clutch system, fuel injection systems ? A4: Launch x431 pad v scan tool can do ECU programming for BMW,for Benz,for Land Rover ,for VW, for Audi, for Porsche, for Nissan, for Infiniti, for Jaguar.but it varies on the car model and the year.
Q5: Will pad v be able to work on my heavy duty trucks ? A5:he heavy Duty Software can be subscribed in 2021.6. you can purchase it in the mall or contact us to get the fatory price($399).and you can directly use the heavy duty software without connectors. it works pretty well with the smart box.
Q6: Will this diagnostic scanner reflash/ reprogram an ecm bcm? A6: This scanner can reflash/reprogramming ECU for 9 brands.support for BMW,for Benz,for Volkswagen, for Audi, for Porsche, for Nissan, for Infiniti, for LAND ROVER, for JAGUAR.other scanner only work for Bens and the BMW.
Q7: Will this remove component protection on a 2018 Audi Q5 gateway module? A7: Yes, it can remove component protection on a 2018 Audi Q5 gateway module.
Q8: Does it have the guide function for my Audi A4? A8: YES! launch x431 pad v automotive scanner have the guide function.it provides step-by-step repair guidance for technicians.the function of guiding the use of the product to prevent the car setting caused by wrong operation.Compatible with VAG series vehicles(Volkswagen / Audi / Skoda / Seat etc.)
Q9: Can this program airbag modules on bmw? A9: yes! launch x431 pad v automotive scanner can program the airbag modules on BMW.this scan tool support intelligent recognition of programming files, convenient and quick operation.Support for BMW,for Benz,for Volkswagen, for Audi, for Porsche, for Nissan, for Infiniti, for LAND ROVER, for JAGUAR.
Q10: Can PAD V perform Key fob for a 2004 Toyota Sienna? A10: Launch x431 pad v scan tool can do key programming for 2004 Toyota Sienna, but you need to get the pin code firstly
Q11: Does OBD1 even work on this scanner? A11: YES! launch x431 pad v automotive scanner comes with 15 obd1 Connectors: TOYOTA-17, HONDA-3, MAZDA-17,FORD-6+1,SSANG YONG-20, CHRYSLER-6, SUBARU-9, KIA-20, DAEWOO-12 ,GEELY-22 ,GMVAZ-12, DAEWOO-12, BMW-20, BENZ-38.Universal-3 12 Cables: GAZ , OBDII-16 EXTEND CABLE , SSANG YONG-14, SUZUKI-3, AUDI-4, FIAT-3, MITSUBISHI HYUNDAI-12+16, OBD1 ADAPTOR, BENZ-14, NISSAN-14+16, DAIHUATSU-4, POWER CABLE CLIPS
Q12: Navigation system for a 2016 Ford Scape in this scanner? A12: LAUNCH X431 PAD V scan tool can read and earse fault codes on Navigation system for a 2016 Ford escape.
Customer feedback:
1.Tony Reyes gives five-star rating: Arrived nicely packaged, this is the best tool I have ever used. This tool is well made, very professional, it does everything you need to diagnose a vehicle. The price is perfect. This is better than any snap on tool I have ever owned. Arrived very quickly. I recommend this tool to everyone and I recommend this seller, excellent service!
2.Matthew Kaufmann gives five-star rating: I like how simple this scan tool is to operate. It’s very quick and gets the job done. I do car repair for a hobby and the price doesn’t break the bank. I purchased this scan tool to do an adaptive learn on a transmission for a 2016 Ford Focus, worked flawlessly.
3.Estid Zecena Diaz gives five-star rating: I think this product is excellent, it is easy to use and efficient. I used it to repair my 2002 toyota camry and it made my job easier. I recommend it.
4.Justin shelby gives five-star rating: This scanner does it all. Very pleased. It is built like a tank it’s a very rugged tool. I HIGHLY recommend this to anyone that needs a professional scanner especially for high end cars. Jessica gives wonderful customer service.
5.Joe gives five-star rating: Superb scanner best of best nice big screen charger station is nice fast smooth J2534 capabilities love the Topoligy breakdown of Can networks and the VCi smartbox can handle it all!
Launch X431 V+ and HD3 Module is more than a professional diagnostic tool for heavy duty truck till 2020 year, it also performs 15 special functions. It’s nice features are Simple tablet appearance, high-definition touch screen (1920*1200), high-speed running speed (Lenovo Tablet TB-X605FC, Android 9，RAM 2G Storage 32GB CPU Snapdragon 450 Display), it also supports multi-language English, German, French, Italy etc.
However, to protect Launch X431 V and data safety, also enjoy the free update, you are required to register a member for the first time.
There are 6 steps to follow:
Step 1. Choose “Login”.
Step 2. Choose “New registration”.
Step 3. Input the user name & password, input the password again. Input the usual email address. Choose the country. Input the CAPTCHA verification code. Tap “Register”.
Step 4. Open the envelope in the product, input the SN number inside, and activate the password–click ACTIVATE
Step 5. Congratulations! you’ve registered successfully, you are ready to use the machine.
Step 6. Software update.
Select all available newest truck software to update, just wait until it succeed.
Besides, after entering “User Info”, there are ” Activate VCI” and “Firmware Fix”, just click on them and follow the screen to do.
It has a wide vehicle brand coverage: truck, bus, machinery, Engine, New Energy.
It optimize a new function “Camera scan VIN”.
It can do: read vehicle information, read DTC, clear fault memory, read data stream, read freeze frame, actuation test, feature and parameter, advanced ECM data.
What’s more, it has one option “Feedback “. In the process of testing, if you can’t test or encounter other problems, you are allowed to submit the logs in testing to the Launch server. Then the engineers will analyze and find out the problem to help you solve it.
This is only for 12V to 24V diesel truck only. If you need to d
عضو شوید
عضویت سریع
آمار مطالب
آمار بازدید
